Penguin

Differences between current version and predecessor to the previous major change of sensors.conf.

Other diffs: Previous Revision, Previous Author, or view the Annotated Edit History

Newer page: version 8 Last edited on Monday, November 7, 2005 8:35:25 am by IanMcDonald
Older page: version 5 Last edited on Sunday, February 20, 2005 6:39:47 am by AlejandroRiveira Revert
@@ -1,4 +1,150 @@
+Gigabyte GA-7N400E  
+ # Sensors 2.9.1 (SuSE 10.0)  
+ chip "it87-*" "it8712-*"  
+  
+ # The values below have been tested on Asus CUSI, CUM motherboards.  
+  
+ # Voltage monitors as advised in the It8705 data sheet  
+  
+ label in0 "VCore 1"  
+ label in1 "VCore 2"  
+ label in2 "+3.3V"  
+ label in3 "+5V"  
+ label in4 "+12V"  
+ label in5 "-12V"  
+ label in6 "-5V"  
+ label in7 "Stdby"  
+ label in8 "VBat"  
+  
+ # vid is not monitored by IT8705F  
+ # comment out if you have IT8712  
+ ignore vid  
+ # in5 and in6 not connected on GA-7N400E  
+ ignore in5  
+ ignore in6  
+ # Incubus Saturnus reports that the IT87 chip on Asus A7V8X-X seems  
+ # to report the VCORE voltage approximately 0.05V higher than the board's  
+ # BIOS does. Although it doesn't make much sense physically, uncommenting  
+ # the next line should bring the readings in line with the BIOS' ones in  
+ # this case.  
+ # compute in0 -0.05+@ , @+0.05  
+  
+ # If 3.3V reads 2X too high (Soyo Dragon and Asus A7V8X-X, and Gigabyte GA-7N400E for example),  
+ # comment out following line.  
+ # compute in2 2*@ , @/2  
+ #  
+ # compute in3 ((6.8/10)+1)*@ , @/((6.8/10)+1)  
+ # compute in4 ((30/10) +1)*@ , @/((30/10) +1)  
+  
+ # This much simpler version seems to work on GA-7N400E  
+ compute in3 2*@ , @/2  
+ compute in4 4*@ , @/4  
+  
+ # For this family of chips the negative voltage equation is different from  
+ # the lm78. The chip uses two external resistor for scaling but one is  
+ # tied to a positive reference voltage. See ITE8705/12 datasheet (SIS950  
+ # data sheet is wrong)  
+ # Vs = (1 + Rin/Rf) * Vin - (Rin/Rf) * Vref.  
+ # Vref = 4.096 volts, Vin is voltage measured, Vs is actual voltage.  
+  
+ # The next two are negative voltages (-12 and -5).  
+ # The following formulas must be used. Unfortunately the datasheet  
+ # does not give recommendations for Rin, Rf, but we can back into  
+ # them based on a nominal +2V input to the chip, together with a 4.096V Vref.  
+ # Formula:  
+ # actual V = (Vmeasured * (1 + Rin/Rf)) - (Vref * (Rin/Rf))  
+ # For -12V input use Rin/Rf = 6.68  
+ # For -5V input use Rin/Rf = 3.33  
+ # Then you can convert the forumula to a standard form like:  
+ compute in5 (7.67 * @) - 27.36 , (@ + 27.36) / 7.67  
+ compute in6 (4.33 * @) - 13.64 , (@ + 13.64) / 4.33  
+ #  
+ # this much simpler version is reported to work for a  
+ # Elite Group K7S5A board  
+ #  
+ # compute in5 -(36/10)*@, -@/(36/10)  
+ # compute in6 -(56/10)*@, -@/(56/10)  
+ #  
+ # compute in7 ((6.8/10)+1)*@ , @/((6.8/10)+1)  
+ #  
+ # GA-7N400E  
+ compute in7 ((8.3/10)+1)*@ , @/((8.3/10)+1)  
+  
+ set in0_min 1.7 * 0.95 #Athlon 2800 vcore is 1.7  
+ set in0_max 1.7 * 1.05  
+ set in1_min 2.6 * 0.95  
+ set in1_max 2.6 * 1.95  
+ set in2_min 3.3 * 0.95  
+ set in2_max 3.3 * 1.05  
+ set in3_min 5.0 * 0.95  
+ set in3_max 5.0 * 1.05  
+ set in4_min 12 * 0.95  
+ set in4_max 12 * 1.05  
+ # set in5_max -12 * 0.95 #Commented out to avoid beeping  
+ # set in5_min -12 * 1.05  
+ # set in6_max -5 * 0.95  
+ # set in6_min -5 * 1.05  
+ set in7_min 5 * 0.95  
+ set in7_max 5 * 1.05  
+ #the chip does not support in8 min/max  
+  
+ # Temperature  
+ #  
+ # Important - if your temperature readings are completely whacky  
+ # you probably need to change the sensor type.  
+ # Adujst and uncomment the appropriate lines below.  
+ # The old method (modprobe it87 temp_type=0xXX) is no longer supported.  
+ #  
+ # 2 = thermistor; 3 = thermal diode; 0 = unused  
+ # set sensor1 3  
+ # set sensor2 3  
+ # set sensor3 3  
+ # If a given sensor isn't used, you will probably want to ignore it  
+ # (see ignore statement right below).  
+  
+ # label temp1 "M/B Temp"  
+ # set temp1_over 40  
+ # set temp1_low 15  
+ # label temp2 "CPU Temp"  
+ # set temp2_over 45  
+ # set temp2_low 15  
+ # ignore temp3  
+ # label temp3 "temp3"  
+ # set temp3_over 45  
+ # set temp3_low 15  
+  
+ # Gigabyte GA-7N400E  
+ label temp1 "M/B Temp"  
+ set temp1_over 50  
+ set temp1_low 15  
+ label temp2 "Air Temp"  
+ set temp2_over 40  
+ set temp2_low 15  
+ label temp3 "CPU Temp"  
+ set temp3_over 80  
+ set temp3_low 15  
+  
+ # The A7V8X-X has temperatures inverted, and needs a conversion for  
+ # CPU temp. Thanks to Preben Randhol for the formula.  
+ # label temp1 "CPU Temp"  
+ # label temp2 "M/B Temp"  
+ # compute temp1 (-15.096+1.4893*@), (@+15.096)/1.4893  
+  
+ # The A7V600 also has temperatures inverted, and needs a different  
+ # conversion for CPU temp. Thanks to Dariusz Jaszkowski for the formula.  
+ # label temp1 "CPU Temp"  
+ # label temp2 "M/B Temp"  
+ # compute temp1 (@+128)/3, (3*@-128)  
+  
+ # Fans  
+ set fan1_min 3000  
+ ignore fan2  
+ # set fan2_min 3000  
+ ignore fan3  
+ # set fan3_min 3000  
+  
+  
 ---- 
 Gigabyte GA-7VTX 
  ###################### 
  # This is my (JohnMcPherson's) /etc/sensors.conf file for the 
@@ -99,9 +245,9 @@
  set temp3_over 65 
  ###################### 
 ---- 
  
-Elite K7s5a motherboard (taken from [ HowToK7s5aHOWTO]
+Elite K7s5a motherboard (taken from HowToK7s5aHOWTO) 
  
  # This motherboard uses an it87 chip, and needs the following 
  # two lines in /etc/modules.conf: 
  # alias char-major-89 i2c-dev 
The following authors of this page have not agreed to the WlugWikiLicense. As such copyright to all content on this page is retained by the original authors.
  • AlejandroRiveira
The following authors of this page have agreed to the WlugWikiLicense.

PHP Warning

lib/plugin/WlugLicense.php (In template 'html'):99: Warning: Invalid argument supplied for foreach()

lib/plugin/WlugLicense.php (In template 'html'):111: Warning: in_array() [<a href='function.in-array'>function.in-array</a>]: Wrong datatype for second argument

lib/plugin/WlugLicense.php (In template 'html'):111: Warning: in_array() [<a href='function.in-array'>function.in-array</a>]: Wrong datatype for second argument