Differences between version 7 and predecessor to the previous major change of sensors.conf.
Other diffs: Previous Revision, Previous Author, or view the Annotated Edit History
Newer page: | version 7 | Last edited on Sunday, October 30, 2005 1:49:37 am | by MaaCruz | Revert |
Older page: | version 5 | Last edited on Sunday, February 20, 2005 6:39:47 am | by AlejandroRiveira | Revert |
@@ -1,4 +1,150 @@
+Gigabyte GA-7N400E
+ # Sensors 2.9.1 (SuSE 10.0)
+ chip "it87-*" "it8712-*"
+
+ # The values below have been tested on Asus CUSI, CUM motherboards.
+
+ # Voltage monitors as advised in the It8705 data sheet
+
+ label in0 "VCore 1"
+ label in1 "VCore 2"
+ label in2 "+3.3V"
+ label in3 "+5V"
+ label in4 "+12V"
+ label in5 "-12V"
+ label in6 "-5V"
+ label in7 "Stdby"
+ label in8 "VBat"
+
+ # vid is not monitored by IT8705F
+ # comment out if you have IT8712
+ ignore vid
+ # in5 and in6 not connected on GA-7N400E
+ ignore in5
+ ignore in6
+ # Incubus Saturnus reports that the IT87 chip on Asus A7V8X-X seems
+ # to report the VCORE voltage approximately 0.05V higher than the board's
+ # BIOS does. Although it doesn't make much sense physically, uncommenting
+ # the next line should bring the readings in line with the BIOS' ones in
+ # this case.
+ # compute in0 -0.05+@ , @+0.05
+
+ # If 3.3V reads 2X too high (Soyo Dragon and Asus A7V8X-X, and Gigabyte GA-7N400E for example),
+ # comment out following line.
+ # compute in2 2*@ , @/2
+ #
+ # compute in3 ((6.8/10)+1)*@ , @/((6.8/10)+1)
+ # compute in4 ((30/10) +1)*@ , @/((30/10) +1)
+
+ # This much simpler version seems to work on GA-7N400E
+ compute in3 2*@ , @/2
+ compute in4 4*@ , @/4
+
+ # For this family of chips the negative voltage equation is different from
+ # the lm78. The chip uses two external resistor for scaling but one is
+ # tied to a positive reference voltage. See ITE8705/12 datasheet (SIS950
+ # data sheet is wrong)
+ # Vs = (1 + Rin/Rf) * Vin - (Rin/Rf) * Vref.
+ # Vref = 4.096 volts, Vin is voltage measured, Vs is actual voltage.
+
+ # The next two are negative voltages (-12 and -5).
+ # The following formulas must be used. Unfortunately the datasheet
+ # does not give recommendations for Rin, Rf, but we can back into
+ # them based on a nominal +2V input to the chip, together with a 4.096V Vref.
+ # Formula:
+ # actual V = (Vmeasured * (1 + Rin/Rf)) - (Vref * (Rin/Rf))
+ # For -12V input use Rin/Rf = 6.68
+ # For -5V input use Rin/Rf = 3.33
+ # Then you can convert the forumula to a standard form like:
+ compute in5 (7.67 * @) - 27.36 , (@ + 27.36) / 7.67
+ compute in6 (4.33 * @) - 13.64 , (@ + 13.64) / 4.33
+ #
+ # this much simpler version is reported to work for a
+ # Elite Group K7S5A board
+ #
+ # compute in5 -(36/10)*@, -@/(36/10)
+ # compute in6 -(56/10)*@, -@/(56/10)
+ #
+ # compute in7 ((6.8/10)+1)*@ , @/((6.8/10)+1)
+ #
+ # GA-7N400E
+ compute in7 ((8.3/10)+1)*@ , @/((8.3/10)+1)
+
+ set in0_min 1.7 * 0.95 #Athlon 2800 vcore is 1.7
+ set in0_max 1.7 * 1.05
+ set in1_min 2.6 * 0.95
+ set in1_max 2.6 * 1.95
+ set in2_min 3.3 * 0.95
+ set in2_max 3.3 * 1.05
+ set in3_min 5.0 * 0.95
+ set in3_max 5.0 * 1.05
+ set in4_min 12 * 0.95
+ set in4_max 12 * 1.05
+ # set in5_max -12 * 0.95 #Commented out to avoid beeping
+ # set in5_min -12 * 1.05
+ # set in6_max -5 * 0.95
+ # set in6_min -5 * 1.05
+ set in7_min 5 * 0.95
+ set in7_max 5 * 1.05
+ #the chip does not support in8 min/max
+
+ # Temperature
+ #
+ # Important - if your temperature readings are completely whacky
+ # you probably need to change the sensor type.
+ # Adujst and uncomment the appropriate lines below.
+ # The old method (modprobe it87 temp_type=0xXX) is no longer supported.
+ #
+ # 2 = thermistor; 3 = thermal diode; 0 = unused
+ # set sensor1 3
+ # set sensor2 3
+ # set sensor3 3
+ # If a given sensor isn't used, you will probably want to ignore it
+ # (see ignore statement right below).
+
+ # label temp1 "M/B Temp"
+ # set temp1_over 40
+ # set temp1_low 15
+ # label temp2 "CPU Temp"
+ # set temp2_over 45
+ # set temp2_low 15
+ # ignore temp3
+ # label temp3 "temp3"
+ # set temp3_over 45
+ # set temp3_low 15
+
+ # Gigabyte GA-7N400E
+ label temp1 "M/B Temp"
+ set temp1_over 50
+ set temp1_low 15
+ label temp2 "Air Temp"
+ set temp2_over 40
+ set temp2_low 15
+ label temp3 "CPU Temp"
+ set temp3_over 80
+ set temp3_low 15
+
+ # The A7V8X-X has temperatures inverted, and needs a conversion for
+ # CPU temp. Thanks to Preben Randhol for the formula.
+ # label temp1 "CPU Temp"
+ # label temp2 "M/B Temp"
+ # compute temp1 (-15.096+1.4893*@), (@+15.096)/1.4893
+
+ # The A7V600 also has temperatures inverted, and needs a different
+ # conversion for CPU temp. Thanks to Dariusz Jaszkowski for the formula.
+ # label temp1 "CPU Temp"
+ # label temp2 "M/B Temp"
+ # compute temp1 (@+128)/3, (3*@-128)
+
+ # Fans
+ set fan1_min 3000
+ ignore fan2
+ # set fan2_min 3000
+ ignore fan3
+ # set fan3_min 3000
+
+
----
Gigabyte GA-7VTX
######################
# This is my (JohnMcPherson's) /etc/sensors.conf file for the