Differences between current version and revision by previous author of HowToBridge.
Other diffs: Previous Major Revision, Previous Revision, or view the Annotated Edit History
| Newer page: | version 3 | Last edited on Thursday, October 21, 2004 5:16:25 pm | by AristotlePagaltzis | |
| Older page: | version 2 | Last edited on Friday, June 7, 2002 1:06:18 am | by perry | Revert |
@@ -1,834 +1 @@
-Bridging mini-HOWTO
-!!!Bridging mini-HOWTO
-!Christopher Cole
-
- cole@coledd.com
-
-
-
-
-March 2001
-
-
-__Revision History__Revision 1.222002-05-20Revised by: tabConverted to Docbook 4.1 SGML and added GFDL per Christopher !ColeRevision 1.212001-03-07Revised by: cc
-
-
-
-
-
-This document describes how to setup an ethernet bridge. What
-is an ethernet bridge? An ethernet bridge is a device that controls data
-packets within a subnet in an attempt to cut down the amount of traffic.
-A bridge is usually placed between two separate groups of computers that
-talk within themselves, but not so much with the computers in the other
-group. A good example of this is to consider a cluster of Macintoshes and
-a cluster of unix machines. Both of these groups of machines tend to be
-quite chatty amongst themselves, and the traffic they produce on the
-network causes collisions for the other machines who are trying to speak
-to one another. A bridge would be placed between these groups of
-computers. The job of the bridge is then to examine the destination of
-the data packets one at a time and decide whether or not to pass the
-packets to the other side of the ethernet segment. The result is a
-faster, quieter network with less collisions.
-
-
-
-
-
-----; __Table of Contents__; 1. Setup; 2. Common Problems; 3. Copyright: ; 3.1. GNU Free Documentation License; 3.2. PREAMBLE; 3.3. APPLICABILITY AND DEFINITIONS; 3.4. VERBATIM COPYING; 3.5. COPYING IN QUANTITY; 3.6. MODIFICATIONS; 3.7. COMBINING DOCUMENTS; 3.8. COLLECTIONS OF DOCUMENTS; 3.9. AGGREGATION WITH INDEPENDENT WORKS; 3.10. TRANSLATION; 3.11. TERMINATION; 3.12. FUTURE REVISIONS OF THIS LICENSE; 3.13. How to use this License for your documents
-!!!1. Setup
-
-
-
-
-
-
-*
-
-Get Bridge Config:
- BRCFG.tgz
-
-
-
-*
-*
-
-BRCFG may also be found at:
- http://coledd.com/networking/bridge
-
-
-
-*
-*
-
-Enable multiple ethernet devices on your machine by
-adding this line to your /etc/lilo.conf,
-and re-run lilo:
-
-append = "ether=,,eth1"
-
-
-
-
-If you have three interfaces on your bridge, use this line instead:
-
-append = "ether=,,eth1 ether=,,eth2"
-
-
-
-
-More interfaces can be found by adding more ether statements.
-By default a stock Linux kernel probes for a single ethercard,
-and once one is found the probe ceases. The above append statement
-tells the kernel to keep probing for more ethernet devices after the
-first one is found.
-Alternatively, the boot parameter can be used instead:
-
-linux ether=,,eth1
-
-
-
-
-Or, with 3 interfaces, use:
-
-linux ether=,,eth1 ether=,,eth2
-
-
-
-*
-*
-
-Recompile the kernel with BRIDGING enabled.
-
-
-
-*
-*
-
-A bridge should not have an IP address.
-It CAN, but a plain bridge doesn't need one.
-To remove the IP address from your bridge, go to
-/etc/sysconfig/network-scripts/ (for a !RedHat system)
-and copy ifcfg-lo0 to ifcfg-eth0 8
-ifcfg-eth1.
-In these two new files, change the line containing
-__DEVICE=lo__ to __DEVICE=eth0__
-and __DEVICE=eth1__.
-Since other distributions may deviate from this, you may need to refer to additional
-documentation.
-If there are more than 2 interfaces to this bridge,
-be sure to make the corresponding configurations to those, as well.
-
-
-
-*
-*
-
-Reboot so you are running the new kernel with BRIDGING in it,
-and also to make sure that an IP addresses are not bound to the
-network interfaces.
-
-
-
-*
-*
-
-Once the system is backed up, put the ethernet cards into promiscuous mode,
-so they will look at every packet that passes by its interface:
-
-ifconfig eth0 promisc ; ifconfig eth1 promisc
-All interfaces which are connected to network segments to be bridged
-are to be put into promiscuous mode.
-
-
-
-*
-*
-
-Turn bridging ON using the brcfg program:
-
-brcfg -ena
-
-
-
-*
-*
-
-Verify that there is different traffic on each interface:
-
-tcpdump -i eth0 (in one window)
-tcpdump -i eth1 (in another window)
-
-
-
-
-*
-*
-
-Run a sniffer or tcpdump on another machine
-to verify the bridge is separating the segment correctly.
-
-
-
-*
-
-----
-!!!2. Common Problems; Q: I get the message ioctl(SIOCGIFBR) failed: Package not installed
-. What does this mean?; Q: Machines on one side cannot ping the other side!; Q: I cannot telnet/ftp from the bridge! Why?; Q: What do I need to set up in the way of routing?; Q: The bridge appears to work, but why doesn't traceroute show the bridge as a part of the path?; Q: Is it necessary to compile IP_FORWARD into the kernel?; Q: Why are the physical ethernet addresses for port 1 and port 2 the
-same according to the brcfg program?
-Shouldn't they be different?; Q: Bridging does not appear to be an option when performing a make
-config on the kernel. How does one enable it?; Q: Too many hubs (4 or more) are chained one after another in series,
-cause timing problems on an ethernet. What effect does a bridge
-have in a subnet that is layered with hubs?; Q: Can a bridge interface to both 10Mb and 100Mb ethernet segments?
-Will such a configuration slow down the rest of the traffic on the
-high speed side?
-
-__Q: __I get the message ioctl(SIOCGIFBR) failed: Package not installed
-. What does this mean?
-
-
-
-__A: __You don't have bridging capability in your kernel.
-Get a 2.0 or greater kernel,
-and recompile with the BRIDGING option enabled.
-
-
-
-__Q: __Machines on one side cannot ping the other side!
-
-
-
-__A: __
-Did you enable bridging using brcfg -ena? (brcfg should say bridging is ENABLED)
-
-Did you put the interfaces into promiscuous mode?
-(issue the ifconfig command.
-The PROMISC flag should be on for
-both interfaces.)
-
-If using multiple-media interface adapters,
-make sure that the correct one is enabled.
-You may need to use the config/setup program that
-came with the network interface card.
-
-
-
-
-__Q: __I cannot telnet/ftp from the bridge! Why?
-
-
-
-__A: __This is because there is no IP address bound to any of bridge
-interfaces. A bridge is to be a transparent part of a network.
-
-
-
-__Q: __What do I need to set up in the way of routing?
-
-
-
-__A: __Nothing!
-All routing intelligence is handled by
-the bridging code in the kernel.
-To see the ethernet addresses as they are learned by the bridge,
-use the brcfg program in debug mode:
-
-
-brcfg -deb
-
-
-__Q: __The bridge appears to work, but why doesn't traceroute show the bridge as a part of the path?
-
-
-
-__A: __Due to the nature of a bridge, a traceroute should NOT show the bridge as a part of the path. A bridge is to be a transparent component of the network.
-
-
-
-__Q: __Is it necessary to compile IP_FORWARD into the kernel?
-
-
-
-__A: __No. The bridging code in the kernel takes care of the packet
-transport.
-IP_FORWARD is for a gateway that has IP addresses
-bound to its interfaces.
-
-
-
-__Q: __Why are the physical ethernet addresses for port 1 and port 2 the
-same according to the brcfg program?
-Shouldn't they be different?
-
-
-
-__A: __No. Every port on a bridge intentionally is assigned the same
-physical ethernet address by the bridging code.
-
-
-
-__Q: __Bridging does not appear to be an option when performing a make
-config on the kernel. How does one enable it?
-
-
-
-__A: __During the kernel config, answer "Y" to the question, Prompt for
-development and/or incomplete code/drivers (CONFIG_EXPERIMENTAL)
[[Y/n/?
].
-
-
-
-__Q: __Too many hubs (4 or more) are chained one after another in series,
-cause timing problems on an ethernet. What effect does a bridge
-have in a subnet that is layered with hubs?
-
-
-
-__A: __A bridge resets the 3/4/5 hubs rule. A bridge does not deal with
-packets the way a hub does, and is therefore not a contributor to
-timing problems on a network.
-
-
-
-__Q: __Can a bridge interface to both 10Mb and 100Mb ethernet segments?
-Will such a configuration slow down the rest of the traffic on the
-high speed side?
-
-
-
-__A: __Yes, a bridge can tie together a 10Mb segment with a 100Mb segment.
-As long as the network card on the fast network is 100Mb capable,
-TCP takes care of the rest. While it's true that the
-packets from a host in the 100Mb network communicating to a host
-in the 10Mb network are moving at only 10Mb/s, the rest of the
-traffic on the fast ethernet is not slowed down.
-
-----
-!!!3. Copyright
-
-Copyright © 2002 Christopher Cole
-
-
-
-Permission is granted to copy, distribute and/or modify this document under the terms of the GNU Free Documentation License, Version 1.1 or any later version published by the Free Software Foundation; with no Invariant Sections, no Front-Cover Texts and no Back-Cover Texts. A copy of the license is included in the section entitled "GNU Free Documentation License".
-
-----
-!!3.1. GNU Free Documentation License
-
-Version 1.1, March 2000
-
-
-
-Copyright (C) 2000 Free Software Foundation, Inc.
-59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
-Everyone is permitted to copy and distribute verbatim copies
-of this license document, but changing it is not allowed.
-
-----
-!!3.2. PREAMBLE
-
-The purpose of this License is to make a manual, textbook,
-or other written document "free" in the sense of freedom: to
-assure everyone the effective freedom to copy and redistribute it,
-with or without modifying it, either commercially or
-noncommercially. Secondarily, this License preserves for the
-author and publisher a way to get credit for their work, while not
-being considered responsible for modifications made by
-others.
-
-
-
-This License is a kind of "copyleft", which means that
-derivative works of the document must themselves be free in the
-same sense. It complements the GNU General Public License, which
-is a copyleft license designed for free software.
-
-
-
-We have designed this License in order to use it for manuals
-for free software, because free software needs free documentation:
-a free program should come with manuals providing the same
-freedoms that the software does. But this License is not limited
-to software manuals; it can be used for any textual work,
-regardless of subject matter or whether it is published as a
-printed book. We recommend this License principally for works
-whose purpose is instruction or reference.
-
-----
-!!3.3. APPLICABILITY AND DEFINITIONS
-
-This License applies to any manual or other work that
-contains a notice placed by the copyright holder saying it can be
-distributed under the terms of this License. The "Document",
-below, refers to any such manual or work. Any member of the
-public is a licensee, and is addressed as "you".
-
-
-
-A "Modified Version" of the Document means any work
-containing the Document or a portion of it, either copied
-verbatim, or with modifications and/or translated into another
-language.
-
-
-
-A "Secondary Section" is a named appendix or a front-matter
-section of the Document that deals exclusively with the
-relationship of the publishers or authors of the Document to the
-Document's overall subject (or to related matters) and contains
-nothing that could fall directly within that overall subject.
-(For example, if the Document is in part a textbook of
-mathematics, a Secondary Section may not explain any mathematics.)
-The relationship could be a matter of historical connection with
-the subject or with related matters, or of legal, commercial,
-philosophical, ethical or political position regarding
-them.
-
-
-
-The "Invariant Sections" are certain Secondary Sections
-whose titles are designated, as being those of Invariant Sections,
-in the notice that says that the Document is released under this
-License.
-
-
-
-The "Cover Texts" are certain short passages of text that
-are listed, as Front-Cover Texts or Back-Cover Texts, in the
-notice that says that the Document is released under this
-License.
-
-
-
-A "Transparent" copy of the Document means a
-machine-readable copy, represented in a format whose specification
-is available to the general public, whose contents can be viewed
-and edited directly and straightforwardly with generic text
-editors or (for images composed of pixels) generic paint programs
-or (for drawings) some widely available drawing editor, and that
-is suitable for input to text formatters or for automatic
-translation to a variety of formats suitable for input to text
-formatters. A copy made in an otherwise Transparent file format
-whose markup has been designed to thwart or discourage subsequent
-modification by readers is not Transparent. A copy that is not
-"Transparent" is called "Opaque".
-
-
-
-Examples of suitable formats for Transparent copies include
-plain ASCII without markup, Texinfo input format, LaTeX input
-format, SGML or XML using a publicly available DTD, and
-standard-conforming simple HTML designed for human modification.
-Opaque formats include !PostScript, PDF, proprietary formats that
-can be read and edited only by proprietary word processors, SGML
-or XML for which the DTD and/or processing tools are not generally
-available, and the machine-generated HTML produced by some word
-processors for output purposes only.
-
-
-
-The "Title Page" means, for a printed book, the title page
-itself, plus such following pages as are needed to hold, legibly,
-the material this License requires to appear in the title page.
-For works in formats which do not have any title page as such,
-"Title Page" means the text near the most prominent appearance of
-the work's title, preceding the beginning of the body of the
-text.
-
-----
-!!3.4. VERBATIM COPYING
-
-You may copy and distribute the Document in any medium,
-either commercially or noncommercially, provided that this
-License, the copyright notices, and the license notice saying this
-License applies to the Document are reproduced in all copies, and
-that you add no other conditions whatsoever to those of this
-License. You may not use technical measures to obstruct or
-control the reading or further copying of the copies you make or
-distribute. However, you may accept compensation in exchange for
-copies. If you distribute a large enough number of copies you
-must also follow the conditions in section 3.
-
-
-
-You may also lend copies, under the same conditions stated
-above, and you may publicly display copies.
-
-----
-!!3.5. COPYING IN QUANTITY
-
-If you publish printed copies of the Document numbering more
-than 100, and the Document's license notice requires Cover Texts,
-you must enclose the copies in covers that carry, clearly and
-legibly, all these Cover Texts: Front-Cover Texts on the front
-cover, and Back-Cover Texts on the back cover. Both covers must
-also clearly and legibly identify you as the publisher of these
-copies. The front cover must present the full title with all
-words of the title equally prominent and visible. You may add
-other material on the covers in addition. Copying with changes
-limited to the covers, as long as they preserve the title of the
-Document and satisfy these conditions, can be treated as verbatim
-copying in other respects.
-
-
-
-If the required texts for either cover are too voluminous to
-fit legibly, you should put the first ones listed (as many as fit
-reasonably) on the actual cover, and continue the rest onto
-adjacent pages.
-
-
-
-If you publish or distribute Opaque copies of the Document
-numbering more than 100, you must either include a
-machine-readable Transparent copy along with each Opaque copy, or
-state in or with each Opaque copy a publicly-accessible
-computer-network location containing a complete Transparent copy
-of the Document, free of added material, which the general
-network-using public has access to download anonymously at no
-charge using public-standard network protocols. If you use the
-latter option, you must take reasonably prudent steps, when you
-begin distribution of Opaque copies in quantity, to ensure that
-this Transparent copy will remain thus accessible at the stated
-location until at least one year after the last time you
-distribute an Opaque copy (directly or through your agents or
-retailers) of that edition to the public.
-
-
-
-It is requested, but not required, that you contact the
-authors of the Document well before redistributing any large
-number of copies, to give them a chance to provide you with an
-updated version of the Document.
-
-----
-!!3.6. MODIFICATIONS
-
-You may copy and distribute a Modified Version of the
-Document under the conditions of sections 2 and 3 above, provided
-that you release the Modified Version under precisely this
-License, with the Modified Version filling the role of the
-Document, thus licensing distribution and modification of the
-Modified Version to whoever possesses a copy of it. In addition,
-you must do these things in the Modified Version:
-
-
-
-
-
-
-#
-
-Use in the Title Page
-(and on the covers, if any) a title distinct from that of the
-Document, and from those of previous versions (which should, if
-there were any, be listed in the History section of the
-Document). You may use the same title as a previous version if
-the original publisher of that version gives permission.
-
-
-#
-#
-
-List on the Title Page,
-as authors, one or more persons or entities responsible for
-authorship of the modifications in the Modified Version,
-together with at least five of the principal authors of the
-Document (all of its principal authors, if it has less than
-five).
-
-
-#
-#
-
-State on the Title page
-the name of the publisher of the Modified Version, as the
-publisher.
-
-
-#
-#
-
-Preserve all the
-copyright notices of the Document.
-
-
-#
-#
-
-Add an appropriate
-copyright notice for your modifications adjacent to the other
-copyright notices.
-
-
-#
-#
-
-Include, immediately
-after the copyright notices, a license notice giving the public
-permission to use the Modified Version under the terms of this
-License, in the form shown in the Addendum below.
-
-
-#
-#
-
-Preserve in that license
-notice the full lists of Invariant Sections and required Cover
-Texts given in the Document's license notice.
-
-
-#
-#
-
-Include an unaltered
-copy of this License.
-
-
-#
-#
-
-Preserve the section
-entitled "History", and its title, and add to it an item stating
-at least the title, year, new authors, and publisher of the
-Modified Version as given on the Title Page. If there is no
-section entitled "History" in the Document, create one stating
-the title, year, authors, and publisher of the Document as given
-on its Title Page, then add an item describing the Modified
-Version as stated in the previous sentence.
-
-
-#
-#
-
-Preserve the network
-location, if any, given in the Document for public access to a
-Transparent copy of the Document, and likewise the network
-locations given in the Document for previous versions it was
-based on. These may be placed in the "History" section. You
-may omit a network location for a work that was published at
-least four years before the Document itself, or if the original
-publisher of the version it refers to gives permission.
-
-
-#
-#
-
-In any section entitled
-"Acknowledgements" or "Dedications", preserve the section's
-title, and preserve in the section all the substance and tone of
-each of the contributor acknowledgements and/or dedications
-given therein.
-
-
-#
-#
-
-Preserve all the
-Invariant Sections of the Document, unaltered in their text and
-in their titles. Section numbers or the equivalent are not
-considered part of the section titles.
-
-
-#
-#
-
-Delete any section
-entitled "Endorsements". Such a section may not be included in
-the Modified Version.
-
-
-#
-#
-
-Do not retitle any
-existing section as "Endorsements" or to conflict in title with
-any Invariant Section.
-
-
-#
-
-If the Modified Version includes new front-matter sections
-or appendices that qualify as Secondary Sections and contain no
-material copied from the Document, you may at your option
-designate some or all of these sections as invariant. To do this,
-add their titles to the list of Invariant Sections in the Modified
-Version's license notice. These titles must be distinct from any
-other section titles.
-
-
-
-You may add a section entitled "Endorsements", provided it
-contains nothing but endorsements of your Modified Version by
-various parties--for example, statements of peer review or that
-the text has been approved by an organization as the authoritative
-definition of a standard.
-
-
-
-You may add a passage of up to five words as a Front-Cover
-Text, and a passage of up to 25 words as a Back-Cover Text, to the
-end of the list of Cover Texts in the Modified Version. Only one
-passage of Front-Cover Text and one of Back-Cover Text may be
-added by (or through arrangements made by) any one entity. If the
-Document already includes a cover text for the same cover,
-previously added by you or by arrangement made by the same entity
-you are acting on behalf of, you may not add another; but you may
-replace the old one, on explicit permission from the previous
-publisher that added the old one.
-
-
-
-The author(s) and publisher(s) of the Document do not by
-this License give permission to use their names for publicity for
-or to assert or imply endorsement of any Modified Version.
-
-----
-!!3.7. COMBINING DOCUMENTS
-
-You may combine the Document with other documents released
-under this License, under the terms defined in section 4 above for
-modified versions, provided that you include in the combination
-all of the Invariant Sections of all of the original documents,
-unmodified, and list them all as Invariant Sections of your
-combined work in its license notice.
-
-
-
-The combined work need only contain one copy of this
-License, and multiple identical Invariant Sections may be replaced
-with a single copy. If there are multiple Invariant Sections with
-the same name but different contents, make the title of each such
-section unique by adding at the end of it, in parentheses, the
-name of the original author or publisher of that section if known,
-or else a unique number. Make the same adjustment to the section
-titles in the list of Invariant Sections in the license notice of
-the combined work.
-
-
-
-In the combination, you must combine any sections entitled
-"History" in the various original documents, forming one section
-entitled "History"; likewise combine any sections entitled
-"Acknowledgements", and any sections entitled "Dedications". You
-must delete all sections entitled "Endorsements."
-
-----
-!!3.8. COLLECTIONS OF DOCUMENTS
-
-You may make a collection consisting of the Document and
-other documents released under this License, and replace the
-individual copies of this License in the various documents with a
-single copy that is included in the collection, provided that you
-follow the rules of this License for verbatim copying of each of
-the documents in all other respects.
-
-
-
-You may extract a single document from such a collection,
-and distribute it individually under this License, provided you
-insert a copy of this License into the extracted document, and
-follow this License in all other respects regarding verbatim
-copying of that document.
-
-----
-!!3.9. AGGREGATION WITH INDEPENDENT WORKS
-
-A compilation of the Document or its derivatives with other
-separate and independent documents or works, in or on a volume of
-a storage or distribution medium, does not as a whole count as a
-Modified Version of the Document, provided no compilation
-copyright is claimed for the compilation. Such a compilation is
-called an "aggregate", and this License does not apply to the
-other self-contained works thus compiled with the Document, on
-account of their being thus compiled, if they are not themselves
-derivative works of the Document.
-
-
-
-If the Cover Text requirement of section 3 is applicable to
-these copies of the Document, then if the Document is less than
-one quarter of the entire aggregate, the Document's Cover Texts
-may be placed on covers that surround only the Document within the
-aggregate. Otherwise they must appear on covers around the whole
-aggregate.
-
-----
-!!3.10. TRANSLATION
-
-Translation is considered a kind of modification, so you may
-distribute translations of the Document under the terms of section
-4. Replacing Invariant Sections with translations requires
-special permission from their copyright holders, but you may
-include translations of some or all Invariant Sections in addition
-to the original versions of these Invariant Sections. You may
-include a translation of this License provided that you also
-include the original English version of this License. In case of
-a disagreement between the translation and the original English
-version of this License, the original English version will
-prevail.
-
-----
-!!3.11. TERMINATION
-
-You may not copy, modify, sublicense, or distribute the
-Document except as expressly provided for under this License. Any
-other attempt to copy, modify, sublicense or distribute the
-Document is void, and will automatically terminate your rights
-under this License. However, parties who have received copies, or
-rights, from you under this License will not have their licenses
-terminated so long as such parties remain in full
-compliance.
-
-----
-!!3.12. FUTURE REVISIONS OF THIS LICENSE
-
-The Free Software Foundation may publish new, revised
-versions of the GNU Free Documentation License from time to time.
-Such new versions will be similar in spirit to the present
-version, but may differ in detail to address new problems or
-concerns. See http://www.gnu.org/copyleft/.
-
-
-
-Each version of the License is given a distinguishing
-version number. If the Document specifies that a particular
-numbered version of this License "or any later version" applies to
-it, you have the option of following the terms and conditions
-either of that specified version or of any later version that has
-been published (not as a draft) by the Free Software Foundation.
-If the Document does not specify a version number of this License,
-you may choose any version ever published (not as a draft) by the
-Free Software Foundation.
-
-----
-!!3.13. How to use this License for your documents
-
-To use this License in a document you have written, include
-a copy of the License in the document and put the following
-copyright and license notices just after the title page:
-
-
-
-Copyright (c) YEAR YOUR NAME.
-Permission is granted to copy, distribute and/or modify this document
-under the terms of the GNU Free Documentation License, Version 1.1
-or any later version published by the Free Software Foundation;
-with the Invariant Sections being LIST THEIR TITLES, with the
-Front-Cover Texts being LIST, and with the Back-Cover Texts being LIST.
-A copy of the license is included in the section entitled "GNU
-Free Documentation License".
-
-
-
-If you have no Invariant Sections, write "with no Invariant
-Sections" instead of saying which ones are invariant. If you have
-no Front-Cover Texts, write "no Front-Cover Texts" instead of
-"Front-Cover Texts being LIST"; likewise for Back-Cover
-Texts.
-
-
-
-If your document contains nontrivial examples of program
-code, we recommend releasing these examples in parallel under your
-choice of free software license, such as the GNU General Public
-License, to permit their use in free software
.
+Describe
[HowToBridge
] here
.
