This document describes various features of HP 's Unix operating system ( HP-UX ) that will affect how Perl version 5 (hereafter just Perl) is compiled and/or runs.
Compiling Perl 5 on HP-UX
When compiling Perl, you must use an ANSI C compiler. The C compiler that ships with all HP-UX systems is a K
Perl can be compiled with either HP 's ANSI C compiler or with gcc. The former is recommended, as not only can it compile Perl with no difficulty, but also can take advantage of features listed later that require the use of HP compiler-specific command-line flags.
If you decide to use gcc, make sure your installation is recent and complete, and be sure to read the Perl README file for more gcc-specific details.
HP 's current Unix systems run on its own Precision Architecture ( PA-RISC ) chip. HP-UX used to run on the Motorola MC68000 family of chips, but any machine with this chip in it is quite obsolete and this document will not attempt to address issues for compiling Perl on the Motorola chipset.
The most recent version of PA-RISC at the time of this document's last update is 2.0.
The original version of PA-RISC , HP no longer sells any system with this chip.
855, 860, 865, 870, 890
An upgrade to the PA-RISC design, it shipped for many years in many different system.
755, 770, 777, 778, 779, 800, 801, 803, 806, 807, 809, 811, 813, 816, 817, 819, 821, 826, 827, 829, 831, 837, 839, 841, 847, 849, 851, 856, 857, 859, 867, 869, 877, 887, 891, 892, 897, A180, A180C, B115, B120, B132L, B132L+, B160L, B180L, C100, C110, C115, C120, C160L, D200, D210, D220, D230, D250, D260, D310, D320, D330, D350, D360, D410, DX0, DX5, DZO, E25, E35, E45, E55, F10, F20, F30, G30, G40, G50, G60, G70, H20, H30, H40, H50, H60, H70, I30, I40, I50, I60, I70, J200, J210, J210XC, K100, K200, K210, K220, K230, K400, K410, K420, S700i, S715, S724, S760, T500, T520
The most recent upgrade to the PA-RISC design, it added support for 64-bit integer data.
895, 896, 898, 899, B1000, C130, C140, C160, C180, C180+, C180-XP, C200+, C400+, C3000, C360, CB260, D270, D280, D370, D380, D390, D650, J220, J2240, J280, J282, J400, J410, J5000, J7000, K250, K260, K260-EG, K270, K360, K370, K380, K450, K460, K460-EG, K460-XP, K470, K570, K580, L1000, L2000, N4000, R380, R390, T540, T600, V2000, V2200, V2250, V2500 A complete list of models at the time the OS was built is in the file /opt/langtools/lib/sched.models. The first column corresponds to the output of the ``uname -m command (without the leading ``9000/). The second column is the PA-RISC version and the third column is the exact chip type used.
Portability Between PA-RISC Versions
It is no longer possible to compile PA-RISC 1.0 executables on either the PA-RISC 1.1 or 2.0 platforms.
Building Dynamic Extensions on HP-UX
HP-UX supports dynamically loadable libraries (shared libraries). Shared libraries end with the suffix .sl.
any functions in other system libraries (e.g., libm), it must be included on this line. (Note that these steps are usually handled automatically by the extension's Makefile).
If these dependent libraries are not listed at shared library creation time, you will get fatal ``Unresolved symbol'' errors at run time when the library is loaded.
You may create a shared library that refers to another library, which may be either an archive library or a shared library. If this second library is a shared library, this is called a ``dependent library''. The dependent library's name is recorded in the main shared library, but it is not linked into the shared library. Instead, it is loaded when the main shared library is loaded. This can cause problems if you build an extension on one system and move it to another system where the libraries may not be located in the same place as on the first system.
If the referred library is an archive library, then it is treated as a simple collection of .o modules (all of which must contain PIC ). These modules are then linked into the shared library.
Note that it is okay to create a library which contains a dependent library that is already linked into perl.
It is no longer possible to link PA-RISC 1.0 shared libraries.
The HP ANSI C Compiler
When using this compiler to build Perl, you should make sure that the flag -Aa is added to the cpprun and cppstdin variables in the config.sh file (though see the section on 64-bit perl below).
Using Large Files with Perl
compiled using structures and functions in which these are 64 bits wide, rather than 32 bits wide. (Note that this will only work with HP 's ANSI C compiler. If you want to compile Perl using gcc, you will have to get a version of the compiler that support 64-bit operations.)
There are some drawbacks to this approach. One is that any extension which calls any file-manipulating C function will need to be recompiled (just follow the usual ``perl Makefile.PL; make; make test; make install'' procedure).
The list of functions that will need to recompiled is: creat, fgetpos, fopen, freopen, fsetpos, fstat, fstatvfs, fstatvfsdev, ftruncate, ftw, lockf, lseek, lstat, mmap, nftw, open, prealloc, stat, statvfs, statvfsdev, tmpfile, truncate, getrlimit, setrlimit
Another drawback is only valid for Perl versions before 5.6.0. This drawback is that the seek and tell functions (both the builtin version and POSIX module version) will not perform correctly.
It is strongly recommended that you use this flag when you run Configure. If you do not do this, but later answer the question about large files when Configure asks you, you may get a configuration that cannot be compiled, or that does not function as expected.
It is possible to compile a version of threaded Perl on any version of HP-UX before 10.30, but it is strongly suggested that you be running on HP-UX 11.00 at least.
added to the list of flags. Also make sure that -lpthread is listed before -lc in the list of libraries to link Perl with.
As of the date of this document, Perl threads are not fully supported on HP-UX .
HP-UX versions before 10.30 require a seperate installation of a POSIX threads library package. Two examples are the HP DCE package, available on `` HP-UX Hardware Extensions 3.0, Install and Core OS , Release 10.20, April 1999 (B3920-13941)'' or the Freely available PTH package, available though worldwide HP-UX mirrors of precompiled packages (e.g. http://hpux.tn.tudelft.nl/hppd/hpux/alpha.html)
Beginning with HP-UX 11.00, programs compiled under HP-UX can take advantage of the LP64 programming environment ( LP64 means Longs and Pointers are 64 bits wide).
Work is being performed on Perl to make it 64-bit compliant on all versions of Unix. Once this is complete, scalar variables will be able to hold numbers larger than 2^32 with complete precision.
As of the date of this document, Perl is not 64-bit compliant on HP-UX .
Should a user wish to experiment with compiling Perl in the LP64 environment, use the -Duse64bitall flag to Configure. This will force Perl to be compiled in a pure LP64 environment (via the +DD64 flag).
You can also use the -Duse64bitint flag to Configure. Although there are some minor differences between compiling Perl with this flag versus the -Duse64bitall flag, they should not be noticeable from a Perl user's perspective.
In both cases, it is strongly recommended that you use these flags when you run Configure. If you do not use do this, but later answer the questions about 64-bit numbers when Configure asks you, you may get a configuration that cannot be compiled, or that does not function as expected.
(Note that these Configure flags will only work with HP 's ANSI C compiler. If you want to compile Perl using gcc, you will have to get a version of the compiler that support 64-bit operations.)
GDBM and Threads
If you attempt to compile Perl with threads on an 11.X system and also link in the GDBM library, then Perl will immediately core dump when it starts up. The only workaround at this point is to relink the GDBM library under 11.X, then relink it into Perl.
NFS filesystems and utime__(2)?__
If you are compiling Perl on a remotely-mounted NFS filesystem, the test io/fs.t may fail on test #18. This appears to be a bug in HP-UX and no fix is currently available.
perl -P and //
In HP-UX Perl is compiled with flags that will cause problems if the -P flag of Perl (preprocess Perl code with the C preprocessor before perl sees it) is used. The problem is that //, being a C ++ -style until-end-of-line comment, will disappear along with the remainder of the line. This means that common Perl constructs like
will turn into illegal code