The configuration file consists of a set of lines. All empty lines, and all text on a line after a '#', will be ignored. Lines may be continued by ending the line with a ''. The remaining lines should all conform to one of the following formats:
[add? above module module_list alias alias_name result [add? below module module_list define VARIABLE WORD depfile=A_PATH else elseif EXPRESSION endif if EXPRESSION include PATH_TO_CONFIG_FILE insmod_opt=GENERIC_OPTIONS_TO_INSMOD install module command ... keep [add? options module MODULE_SPECIFIC_OPTIONS path=A_PATH path[TAG?=A_PATH generic_stringfile=A_PATH pcimapfile=A_PATH isapnpmapfile=A_PATH usbmapfile=A_PATH parportmapfile=A_PATH ieee1394mapfile=A_PATH pnpbiosmapfile=A_PATH [add? probe name module_list [add? probeall name module_list prune filename post-install module command ... post-remove module command ... pre-install module command ... pre-remove module command ... remove module command ... persistdir directory_name All arguments to a directive will be processed to handle shell meta-characters, which means that
path[misc?/lib/modules/1.1.5?/local path[net?/lib/modules/`uname -r`/net DANGER: Applying shell expansion to user supplied input is a major security risk. Modutils code only does meta expansion via shell commands for trusted data. Basically this means only for data in the config file. Even that assumes that the user cannot run modprobe as root while supplying their own config file. Programs (including the kernel) that invoke modutils programs as root with user supplied input must pass exactly one user supplied parameter and must set safe mode or risk creating local root exploits. See modprobe for details on safe mode.
A_PATH is the fully qualified path to the target. It is possible to use shell meta-characters in A_PATH including command output, such as uname -r and kernelversion. These two commands are also understood internally in these utilities as meaning the version number of the current kernel and the current kernel version respectively (e.g.: 2.2.3 and 2.2).
WORD is a sequence if non-white characters. If ' WORD will then be expanded w.r.t. meta-characters. If the expanded result gives more than one word then only the first word of the result will be used.
EXPRESSION below can be:
WORD compare_op WORD
where compare_op is one of ==, !=,
-n WORD compare_op WORD
where compare_op is one of ==, !=,
If the expansion of WORD fails, or if the expansion is
Test if the file FILENAME exists.
This is a description of the legal directives.
define VARIABLE WORD
Do a putenv( Variables can be created and modified by this directive. The variables will be available in the environment, which makes them usable for all commands executed in the current session.
This is the path to the dependency file that will be created by depmod and used by modprobe to find the modules and their dependent modules. Normally the default value should be used, see below.
If the expression is evaluated to be TRUE then all directives up to the matching else, elseif or endif are processed. Otherwise they are ignored. if directives may be nested up to an internal maximum of 20. Note: please avoid having any path directives conditionally processed. Since modprobe has enough built-in path directive will gain you nothing but confusion. Really.
If the previous matching if or elseif directive evaluated its expression to be FALSE then the directives enclosed by the (optional) else directive and its matching endif directive will be processed.
If the previous matching if or elseif directives evaluated their expression to be FALSE and if the expression for this directive evaluates to TRUE then the directives up to the next matching elseif, else or endif directive will be processed.
This directive ends the chain of matching if, elseif or else directive(s) controlling the conditional processing of configuration file directives.
if EXPRESSION any config lines elseif EXPRESSION any config lines else any config lines endif The else and elseif directives are optional.
To handle different platforms or configurations with a single configuration file can be quite complex. With the use of the include directive, conditionally processed by if directives, this is now easier to handle.
If insmod should need some special options, not specified elsewhere, this directive makes it possible to add such an option, to be used for every invocation. The standard default options to insmod does normally not have to be modified unless some special situation needs to be handled.
If this word is found on a line before any lines that contain the path descriptions, the default set of paths will be saved, and thus added to. Otherwise the normal behavior is that the default set will be replaced by the set of paths in the configuration file.
The A_PATH argument specifies an additional directory to search for modules. The path directive can carry an optional tag. This tells us a little more about the purpose of the modules in this directory and allows some automated operations by modprobe. The tag is appended to the One very useful tag is boot, which can be used to mark all directories containing modules that should be loaded at boot-time. Note that you must specify the keep directive to prevent any path__ directives from over-riding the default paths.
This is the path to the generic_string file that will be created by depmod and used by install scripts that need string information from modules. Normally the default value should be used, see below. pcimapfile=A_PATH This is the path to the pcimap file that will be created by depmod and used by install scripts to find the module that supports a pci device. Normally the default value should be used, see below.
This is the path to the isapnpmap file that will be created by depmod and used by install scripts to find the module that supports an ISA PNP device. Normally the default value should be used, see below.
This is the path to the usbmap file that will be created by depmod and used by install scripts to find the module that supports an USB device. Normally the default value should be used, see below.
This is the path to the parportmap file that will be created by depmod and used by install scripts to find the module that supports an parport device. Normally the default value should be used, see below.
This is the path to the ieee1394map file that will be created by depmod and used by install scripts to find the module that supports an ieee1394 device. Normally the default value should be used, see below.
This is the path to the pnpbiosmap file that will be created by depmod and used by install scripts to find the module that supports an pnpbios device. Normally the default value should be used, see below.
alias alias_name result
alias iso9660 isofs makes it possible to write modprobe iso9660 although there is no object file for such a module available. Note that the line:
alias some_module off will make modprobe ignore requests to load that module. Another special alias is:
alias some_module null which will make requests for some_module always succeed, but no module will actually be installed. This can be used as a base for stacks created via the above and below directives.
It is possible to have a large number of levels of alias directives, since all aliases will be recursively expanded in order to find the physical module actually referred to. There is an arbitrary limit of 1000 on alias depth to detect loops like:
alias a b alias b a If the final result of an alias mapping does not match the name of any module then modprobe applies probe and probeall mappings to the result. If those do not succeed then the module is not found. This makes constructs like this give sensible results (from devfs).
alias /dev/sg* /dev/sg probeall /dev/sg scsi-hosts sg It is legal for an alias to map module A to module B and for module A to exist at the same time but this construct is ambiguous and is not recommended. For historical reasons, the kernel sound system has a module called sound.o but the sound developers also want an alias from sound to the module for the user's sound card, e.g. __
[add? probe name module_list
[add? probeall name module_list
These directives can only be used when name is the name of the module requested on the command line of modprobe. The effect is that when a request for name is made, the modules in module_list will be tried, in the specified order. The difference between the directives is that probe will continue until the first successful module insertion, while probeall will continue until the end of the list. The exit status reflects whether any module has been successfully installed or not. The optional add prefix adds the new list to the previous list instead of replacing it.
The top level module directory for a kernel install contains files which are not modules. These include modules.dep, modules.generic_string, modules.pcimap, modules.isapnpmap, modules.usbmap, modules.parportmap, modules.ieee1394map, modules.pnpbiosmap, the build symlink to the kernel source tree and any other files that the install process wants to save from a kernel build. To prevent depmod issuing warnings about depmod has a built in prune list which cannot be removed because it lists files which will exist for any kernel build. If you add your own files to the top level modules directory, add a prune statement for each filename. Note: The prune list is only used when scanning the top directory of a path, and only if the directory contains at least one subdirectory from the standard list of subdirectory names, i.e. it appears to be a top level directory built from a kernel install. The prune list has no effect on subdirectories of a path.
All module names, including aliased names, can have their own options directives. Options specified for an alias have higher priority than the options specified for more options directives. Options given on the command line have the highest priority. If there is -k before the module name, then the module won't be autocleaned even if modprobe has been invoked with the -k autoclean option. The optional add prefix adds the new list to the previous list instead of replacing it. If the result of an alias is not a real module then any options that were constructed from the alias chain are discarded before invoking probe[all?. If any of the MODULE_SPECIFIC_OPTIONS contain characters that are special to the shell (e.g. space, comma, parentheses) then the option must be enclosed in ' ''
[add? above module module_list
This directive makes it possible for one module to lsmod(8) command. The above directive is useful for those circumstances when the dependencies are more complex than what can be described in the modules.dep dependency file. This is an optimized case of the post-install and pre-remove directives. Note that failure of installing the module will not influence the exit status of modprobe.__ The optional add prefix adds the new list to the previous list instead of replacing it.
[add? below module module_list
This directive makes it possible for one module to lsmod(8) command. The below directive is useful for those circumstances when the dependencies are more complex than what can be described in the modules.dep dependency file. This is an optimized case of the pre-install and post-remove directives. Note that failure of installing the module will not influence the exit status of modprobe.__ The optional add prefix adds the new list to the previous list instead of replacing it.
The following directives are useful for (optionally) executing specific commands when loading and unloading a module. Note that even aliased module names can have these directives, which will be executed in the proper order together with any directives for the unaliased module name.
pre-install module command
Execute command before installing the specified module. See the below directive as well.
install module command
Execute command instead of the default insmod when installing the specified module.
post-install module command
Execute command after installing the specified module. See the above directive as well.
pre-remove module command
Execute command before removing the specified module. See the above directive as well.
remove module command
Execute command instead of the default (built-in) rmmod when removing the specified module.
post-remove module command
Execute command after removing the specified module. See the below directive as well.
When rmmod removes a module that contains persistent module parameters, it stores the (possibly) modified parameters underneath directory_name. When modprobe loads a module that contains persistent module parameters, it looks under directory_name for any previous values for those parameters. You must set persistdir to the name of a directory that is readable when modules are loaded and is writable when modules are unloaded, the default value is /var/lib/modules/persist. Many Linux distributions load their modules before mounting filesystems, this can cause problems for persistent data. If /var is a separate partition and it is mounted after modules are loaded then insmod has nowhere to read persistent data from. You have two choices when /var is on a separate partition.
1) Specify persistdir pointing at a directory in the root partition, say /lib/modules/persist. This assumes that the root partition is writable when rmmod runs.
If the configuration file '/etc/modules.conf' is missing, or if any directive is not overridden, the following defaults are assumed:
There are also a set of default alias and options directives. Since this set is continuously extended, no list will be given here. The (current) default set can be viewed by using the modprobe -c command with an empty /etc/modules.conf file.
All options directives specify the options needed for a module, as in:
modprobe de620 bnc=1 These options will be overridden by any options given in the /etc/modules.conf file, and on the modprobe command line.
Remember that it is possible to have an options directive for aliased module names as well as for the non-aliased name. This is useful for e.g. the dummy module: