WAVELAN_CS(S) WAVELAN_CS(S) NAME wavelan_cs - AT&T GIS WaveLAN PCMCIA device driver SYNOPSIS insmod wavelan_cs.o [irq_list=i,j,...] [mem_speed=n] [do_roaming=n] DESCRIPTION wavelan_cs is the low-level Card Services driver for the NCR / AT&T / Lucent WaveLAN PCMCIA and Digital (DEC) Roam- About DS wireless ethernet adapter. When this driver is attached to a card, it allocates the next available ether- net device (eth0..eth#). This device name will be passed on to cardmgr(r) for the card configuration, and reported in the kernel log file with the MAC address, NWID and fre- quency used by the card. PARAMETERS irq_list=i,j,... Specifies the set of interrupts that may be allo- cated by this driver. mem_speed=n Sets the access speed of the shared memory window, in nanoseconds. The default is 0 (i.e., no extra wait states). do_roaming=n Enables or disables roaming mode. The default is 1 (roam). WIRELESS EXTENSIONS Use iwconfig(g) to manipulate wireless extensions. Network ID Set the network ID [0 to FFFF] or disable it [off] or reenable it [on]. As the NWID is stored in the card Per- manent Storage Area, it will be reuse at any further invo- cation of the driver. Frequency & channels For the 2.4GHz 2.00 Hardware, you are able to set the fre- quency by specifying one of the 10 defined channels (2.412, 2.422, 2.425, 2.4305, 2.432, 2.442, 2.452, 2.460, 2.462 or 2.484) or directly by its value. The frequency is changed immediately and permanentely. Frequency availabil- ity depend on the regulations... Sensitivity Signal level threshold for packet reception [0 to 63]. Should be set according to the ambiant noise level. Encryption key Set the encryption key [0 to FFFF-FFFF-FFFF-FFFF]. Use [off] and [on] to disable and reenable the hardware encryption. This feature works only for device with encryption option (DES or AES). Statistics spy Set a list of MAC addresses in the driver (up to 8) and get the last quality of link for each of those (see iwspy(y)). /proc/net/wireless status is the status reported by the modem. Link quality reports the quality of the modulation on the air (direct sequence spread spectrum) [max = 16]. Level and Noise refer to the signal level and noise level [max = 64]. The crypt discarded packet and misc discarded packet counters are not implemented. PRIVATE IOCTL You may use iwpriv(v) to manipulate private ioctls. Quality threshold Enable you the define the quality threshold used by the modem (packet below that level are discarded). Histogram This functionality allow to set a number of signal level intervals and to count the number of packets received in each of those defined intervals. This distribution might be used to calculate the mean value and standard deviation of the signal level. OTHER FEATURES Hot unplug support. Power saving (use 'ifconfig down'). SPECIFIC NOTES This driver will fail to load some non NCR/ATT&T/Lucent Wavelan cards. If it's your case, you must look in the source code on how to add your card to the detection rou- tine. Some of the mentioned features are optional. You may enable to disable them by changing flags in the driver header and recompile. AUTHOR Anthony D. Joseph - adj@lcs.mit.edu Jean Tourrilhes - jt@hplb.hpl.hp.com (+ others - see source code for details) SEE ALSO wavelan(n), cardmgr(r), pcmcia(a), ifconfig(g), insmod(d), iwconfig(g), iwspy(y), iwpriv(v). MIT Lab. for Comp. Sci. 4/16/95 WAVELAN_CS(S)