sane-umax_pp(p) sane-umax_pp(p) NAME sane-umax_pp - SANE backend for Umax parallel port flatbed scanners DESCRIPTION The sane-umax_pp library implements a SANE (Scanner Access Now Easy) backend that provides access to Umax parallel port flatbed scanners. The following scanners work with this backend: Model: -------------------- Astra 1220P HP3200C Astra 1600P Astra 2000P This backend handles 75x75, 150x150, 300x300, 600x600 and 600x1200 dpi scan resolutions, in color and gray levels. There is no lineart mode. These scanners share the same ASIC. Only parts such as CCD and ADC change from one to another. They even all reports being UMAX Astra 1220P via IEEE1284. There isn't direct way to recognize them properly. Under windows, model is set by the driver, regardless of the hardware. EPP MODE ONLY The current version of the backend use only EPP mode to communicate with the scanner. PS/2 and SPP mode aren't implemented. It is recommended that you set your parallel port to EPP in BIOS with the cur- rent version of this backend. ECPEPP will only work if you use a 2.4 kernel with ppdev character device support. This backend does support parport sharing only if you have a kernel with ppdev support. Note that the backend needs to run as root. To allow user access to the scanner run the backend through the network interface (See saned(d) and sane-net(t)). A more relaxed solution (security wise) is to add suid bit to the fron- tend (See chmod(d)). The backend drop root priviledges as soon as it can, right after gaining direct access to IO ports. DEVICE NAMES This backend expects device names of the form: port addr Where addr is the base address of the port your scanner is attached to. Known ports are 0x378 (lp1) 0x278 (lp2) and 0x3BC (lp0). Note that if you are using a Kernel 2.2.x or better , the first parallel port is named lp0 regardless of the base address. However, this backend requires the base address of your port. If you are not sure which port your scanner is connected to, have a look at your /etc/conf.modules. You can rename any device using the name devname model model vendor vendor options. These options apply to the last port option. CONFIGURATION Please make sure to edit umax_pp.conf before you use the backend. The contents of the umax_pp.conf file is a list of options and device names that correspond to Umax scanners. Empty lines and lines starting with a hash mark (#) are ignored. The height options supported are red-gain, green-gain, blue-gain, red-highlight, green-highlight, blue-highlight, astra, and buffer. Options red-gain , green-gain and blue-gain allow you to adjust the sensitivy of your scanner for the given color. Values range from 0 (lowest gain) to 15 (highest). When all three gains are set to 0, the backend does auto gain tuning. Options red-highlight , green-highlight and blue-highlight allow you to adjust the highlight of your scanner for the given color. Values range from 0 (lowest highlight) to 15 (highest). Option astra allows you to change the model of your scan- ner. Current auto detection is based on side effects on scanning when using 1220P command set on other models, so it may fail on unkown hardware combination. Valid values are 1220, 1600 and 2000. Option buffer allows you to change the size of the scan buffer. The size must be specified in bytes. The default value is 2 megabytes. FILES /etc/sane.d/umax_pp.conf The backend configuration file (see also descrip- tion of SANE_CONFIG_DIR below). /usr/lib/sane/libsane-umax_pp.a The static library implementing this backend. /usr/lib/sane/libsane-umax_pp.so The shared library implementing this backend (pre- sent on systems that support dynamic loading). ENVIRONMENT SANE_CONFIG_DIR This environment variable specifies the list of directories that may contain the configuration file. Under UNIX, the directories are separated by a colon (`:'), under OS/2, they are separated by a semi-colon (`;'). If this variable is not set, the configuration file is searched in two default directories: first, the current working directory (".") and then in /etc/sane.d. If the value of the environment variable ends with the directory sepa- rator character, then the default directories are searched after the explicitly specified directo- ries. For example, setting SANE_CONFIG_DIR to "/tmp/config:" would result in directories "tmp/config", ".", and "/etc/sane.d" being searched (in this order). SANE_DEBUG_UMAX_PP If the library was compiled with debug support enabled, this environment variable controls the debug level for this backend. E.g., a value of 128 requests all debug output to be printed. Smaller levels reduce verbosity. level debug output ------- ------------------------------ 0 nothing 1 errors 2 warnings & minor errors 3 additional information 4 debug information 5 code flow (not supported yet) 6 special debug information SANE_DEBUG_UMAX_PP_LOW This variable sets the debug level for the SANE interface for the Umax ASIC. Note that enabling this will spam your terminal with some million lines of debug output. level debug output ------- ------------------------------- 0 nothing 1 errors 8 command blocks 16 detailed code flow 32 dump datafiles 255 everything SEE ALSO sane(e), sane-net(t), saned(d) For latest bug fixes and information see http://umax1220p.sourceforge.net/ AUTHOR Stphane VOLTZ <svoltz@wanadoo.fr>, man page derived from mustek_pp man page by Jochen Eisinger <jochen.eisinger@gmx.net> BUG REPORTS If something doesn't work, please contact me. But I need some information about your scanner to be able to help you... SANE version run "scanimage -V" to determine this the backend version and your scanner hardware run "SANE_DEBUG_UMAX=255 scanimage -L 2>log" as root. If you don't get any output from the umax_pp backend, make sure a line "umax_pp" is included into your /etc/sane.d/dll.conf. If your scanner isn't detected, make sure you've defined the right port address in your umax_pp.conf. the name of your scanner/vendor also a worthy information. Please also include the optical resolution and lamp type of your scanner, both can be found in the manual of your scanner. any further comments if you have comments about the documentation (what could be done better), or you think I should know something, please include it. 28 April 2001 sane-umax_pp(p)