dictzip compresses files using the gzip(1) algorithm (LZ77) in a manner which is completely compatible with the gzip file format. An extension to the gzip file format (Extra Field, described in 220.127.116.11 of RFC 1952) allows extra data to be stored in the header of a compressed file. Programs like gzip and zcat will ignore this extra data. However, dictd(8), the DICT protocol dictionary server will make use of this data to perform pseudo-random access on the file. Files in the dictzip format should end in gzip files that do not contain the special header information.
From RFC 1952, the extra field is specified as follows:
If the FLG.FEXTRA bit is set, an
SI1 and SI2 provide a subfield ID, typically two ASCII letters with some mnemonic value. Jean-Loup Gailly
LEN gives the length of the subfield data, excluding the 4 initial bytes.
The dictzip program uses 'R' for SI1, and 'A' for SI2 (i.e., __
As per RFC 1952, all data is stored least-significant byte first. For VER 1 of the data, all values are 16-bits long (2 bytes), and are unsigned integers.
XLEN (which is specified earlier in the header) is a two byte integer, so the extra field can be 0xffff bytes long, 2 bytes of which are used for the subfield ID (SI1 and SI1), and 2 bytes of which are used for the subfield length (LEN). This leaves 0xfffb bytes (0x7ffd 2-byte entries or 0x3ffe 4-byte entries). Given that the zip output buffer must be 10% + 12 bytes larger than the input buffer, we can store 58969 bytes per entry, or about 1.8GB if the 2-byte entries are used. If this becomes a limiting factor, another format version can be selected and defined for 4-byte entries.
For compression, the file is divided up into
True random file access is not realized, since any access, even for a single byte, requires that a 64kB chunk be read and decompressed. This is slower than accessing a flat text file, but is much, much faster than performing serial access on a fully compressed file.
-d or --decompress
Decompress. This is the default if the executable is called dictunzip.
-c or --stdout
Write output on standard output; keep original files unchanged. This is only available when decompressing (because parts of the header must be updated after a write when compressing).
-f or --force
Force compression or decompression even if the output file already exists.
-h or --help
-k or --keep
Do not delete the original file.
-l or --list
For each compressed file, list the following fields:
type: dzip, gzip, or text (includes files in unknown formats) crc: CRC checksum date and time: from header chunks: number of chunks in file size: size of each uncompressed chunk compr.: compressed size uncompr.: uncompressed size ratio: compression ratio (0.0% if unknown) name: name of uncompressed file
Unlike gzip, the compression method is not detected.
-L or --license
Display the dictzip license and quit.
-t or --test
Check the compressed file integrity. This option is not implemented. Instead, it will list the header information.
-v or --verbose
Verbose. Display extra information during compression.
-V or --version
Version. Display the version number and compilation options then quit.
-s start or --start start
Specify the offer to start decompression, using decimal numbers. The default is at the beginning of the file.
-e size or --size size
Specify the size of the portion of the file to decompress, using decimal numbers. The default is the whole file.
-S start or --Start start
Specify the offer to start decompression, using base64 numbers. The default is at the beginning of the file.
-E size or --Size start
Specify the size of the portion of the file to decompress, using base64 numbers. The default is the whole file.
-p prefilter or --pre prefilter
Specify a shell command to execute as a filter before compression or decompression of a chunk. The pre- and post-compression filters can be used to provide additional compression or output formatting. The filters may not increase the buffer size significantly. The pre- and post-compression filters were designed to provide the most general interface possible.
-P postfilter or --post postfilter
dictzip was written by Rik Faith (email@example.com) and is distributed under the terms of the GNU General Public License. If you need to distribute under other terms, write to the author.