What is Ethernet Bonding

Ethernet bonding refers to aggregating multiple ethernet channels together to form a single channel. This is primarily used for redundancy in ethernet paths or for load balancing. This page refers in particular to performing ethernet bonding under linux, and so does not limit itself to discussion of 802.3ad Trunk Aggregation.

Bonding Types

The linux kernel bonding module supports a number of bonding types.

• Round Robin

  • Packets are transmitted in a round robin fashion over the available slave interfaces. Provides both load balancing and fault tolerance

• Active Backup

  • One slave interface is active at any time. If one interface fails, another interface takes over the MAC address and becomes the active interface. Provides fault tolerance only. Doesn't require special switch support

• Balance XOR

  • Tranmissions are balanced across the slave interfaces based on ((source MAC) XOR (dest MAC)) modula slave count. The same slave is selected for each destination MAC. Provides load balancing and fault tolerance.

• Broadcast

  • Transmits everything on all slave interfaces. Provides fault tolerance.

• 802.3ad

  • This is classic IEEE 802.3ad Dynamic link aggregation. This requires 802.3ad support in the switch and driver support for retrieving the speed and duplex of each slave.

• Balance TLB

  • Adaptive Transmit Load Balancing. Incoming traffic is received on the active slave only, outgoing traffic is distributed according to the current load on each slave. Doesn't require special switch support

• Balance ALB

  • Adaptive Load Balancing - provides both transmit load balancing (TLB) and receive load balancing for IPv4 via ARP negotiation. Doesn't require special switch support, but does require the ability to change the MAC address of a device while it is open

Tools

You need the bonding module for your kernel, and the ifenslave tool which is found within the kernel source at Documentation/networking/ifenslave.c, or you could use a distribution provided package (eg, apt-get install ifenslave-2.4 or apt-get install ifenslave-2.6 depending on your kernel version).

Module alias

It is recommended that you let the kernel know which module to use for the bonded interface by setting the following in the appropriate place for module options (for debian it is /etc/modutils/aliases):

alias bond0 bonding

Module options

When loading the bonding module, you must specify the mode you wish to use. It's normally best to set this as a modprobe option, the location of which will depend on your distribution. For debian, you could set it in /etc/modutils/options and run update-modules

Read the kernel docs for which options are supported. At a minimum, you have to set the bonding mode you wish to use, eg:

options bond0 mode=802.3ad miimon=100

Creating the bonded interface

To bond eth0 and eth1 into the bonded device bond0, and assign this device the IP address 192.168.1.1 within the 192.168.1.0/24 network, do the following:

ifconfig bond0 192.168.1.1 netmask 255.255.255.0 up
ifenslave bond0 eth0
ifenslave bond0 eth1

Your distribution will possibly have native interface control support for creating bonded interfaces. Check your manual pages. RedHat and SuSE (and derivatives) have native support; debian doesn't appear to.

An example of how to do this within debian is as follows:

auto eth0 eth1 bond0

iface eth0 inet manual

iface eth1 inet manual

iface bond0 inet static
    pre-up ifconfig bond0 up
    pre-up ifenslave bond0 eth0 eth1
    pre-down ifenslave -d bond0 eth0 eth1
    address 192.168.1.1
    netmask 255.255.255.0
    network 192.168.1.0
    broadcast 192.168.1.255
    gateway 192.168.1.254

There is a mailing list post which contains some hook scripts for debian to provide ifupdown bonded interface functionality. These can be found here

VLANs

You can specify VLAN interfaces on top of a bonded interface. Simply assign the bond0 interface no IP address (or 0.0.0.0), and then you can use the bond0 interface as the physical device for the VLAN interface. Refer to your distribution documentation on how to setup vlans within your network configuration.

References

• Linux kernel documentation, Documentation/networking/bonding.txt
• http://www.debian-administration.org/articles/312