Differences between current version and predecessor to the previous major change of HowToDPTHardwareRAID.
Other diffs: Previous Revision, Previous Author, or view the Annotated Edit History
| Newer page: | version 3 | Last edited on Monday, October 25, 2004 2:23:19 am | by StuartYeates | |
| Older page: | version 2 | Last edited on Friday, June 7, 2002 1:06:27 am | by perry | Revert |
@@ -1,758 +1 @@
-
-
-
-Linux DPT Hardware RAID mini-HOWTO
-
-
-
-----
-
-!!! Linux DPT Hardware RAID mini-HOWTO
-
-!!Ram Samudrala (me@ram.org) v1.6, February 20, 2002
-
-
-----
-''How to set up hardware RAID under Linux.''
-----
-
-
-
-
-!!1. Introduction
-
-
-
-
-!!2. Supported controllers
-
-
-*2.1 DPT controllers
-
-*2.2 ICP vortex controllers
-
-
-
-
-
-!!3. What hardware should be used?
-
-
-*3.1 Controller type
-
-*3.2 Enclosure type
-
-
-
-
-
-!!4. Installation
-
-
-*4.1 Installing and configuring the hardware
-
-*4.2 Configuring the kernel
-
-*4.3 Bootup messages
-
-
-
-
-
-!!5. Usage
-
-
-*5.1 fdisk, mke2fs, mount, etc.
-
-*5.2 Hot swapping
-
-*5.3 Performance
-
-
-
-
-
-!!6. Features in the EATA DMA driver
-
-
-
-
-!!7. Troubleshooting
-
-
-*7.1 Upon bootup, no SCSI hosts are detected
-
-*7.2 RAID configuration shows up as N different disks
-
-*7.3 Machine/controller is shut down in the middle of a format
-
-*7.4 SCSI_ABORT_BUSY errors produced during initial filesystem format
-
-*7.5 If all fails...
-
-
-
-
-
-!!8. References
-
-
-
-
-!!9. Acknowledgements
-----
-
-!!1. Introduction
-
-
- This document describes how to set up SCSI hardware RAID, focusing
-mainly on host-based adapters from DPT, though the principles applied
-here are fairly general.
-
-
- Use the information below at your own risk. I disclaim all
-responsibility for anything you may do after reading this HOWTO. The
-latest version of this HOWTO will always be available at
-http://www.ram.org/computing/linux/dpt_raid.html.
-
-
- For the purposes of this HOWTO, I am assuming you have only a
-Linux system running. Also, note that I've only tried this out with
-the DPT Smartcache IV PM2144UW and PM3334UW controllers, with DPT
-(SmartRAID tower) and Wetex enclosures, and I have no experience with
-other setups. So things may be different for your setup.
-----
-
-!!2. Supported controllers
-
-
- One well-supported host-based hardware RAID controller (i.e, a
-controller for which there exists a driver under Linux) is one that is
-made by
-DPT. However, there
-exist other host-based and SCSI-to-SCSI controllers which may work
-under Linux. These include the ones made by
-Syred,
-ICP-Vortex, and
-!BusLogic. See the
-RAID solutions for Linux page for more info.
-
-
- If, in the future, there is support for other controllers, I will
-do my best to incorporate that information into this HOWTO. Please
-send me any such information you think is appropriate for this
-HOWTO.
-
-!!2.1 DPT controllers
-
-
-
- This document is currently DPT-oriented. Essentially all the
-SmartRAID IV controllers are supported.
-
-!!2.2 ICP vortex controllers
-
-
-
- ICP vortex has a complete line of disk array controllers which
-support Linux. The ICP driver is in the Linux kernel since version
-2..31. All major Linux Distributors S.u.S.e., LST Power Linux, Caldera
-and Red Hat support the ICP controllers as boot/installation
-controllers. The RAID system can easily be configured with their
-ROMSETUP (you do not have to boot MS-DOS for configuration!).
-
-
- With the monitoring utility GDTMON it is possible to manage the
-complete ICP RAID system during operation (check transfer rates, set
-parameters for the controller and hard disks, exchange defective hard
-disks, etc.). Currently available are: 1 and 2 channel wide and ultra
-SCSI controller for RAID 0 and RAID 1 1, 2, 3 and 5 chn. wide and
-ultra SCSI controller for RAID , 1, 4, 5 and 10 1 and 2 channel wide
-and ultra2 LVDS SCSI controller for RAID 0 and RAID 1 1, 2, 3 and 5
-chn. wide and ultra2 LVDS SCSI controller for RAID , 1, 4, 5 and 10 1
-and 2 port Fibre Channel controllers for RAID , 1, 4, 5 and 10 Pretty
-soon there will be also 64-bit controllers available.
-
-
- ICP is transitioning the entry-level RS series from Ultra2 SCSI to
-Ultra160 SCSI. The drivers, firmware, features, capabilities etc
-remain the same. They are still 32 Bit cards with the i960RS
-processor working at 100MHz. The only difference is they will work at
-Ultra160 (data transfer rate of 160MB/sec) rather than Ultra2 (data
-transfer of 80MB/sec).
-
-
- Effective immediately, the GDT7523RN units will become GDT8523RZ
-and the GDT7623RN units will become GDT8623RZ. The transition from
-33MHz on the PCI bus to 66MHz represents a huge potential performance
-increase. The new cards will have the new Intel 80303 "Zion"
-processor, allowing bus master transfer rates of up to 528MB/sec, and
-will take up to 256MB of ECC RAM on PC133 SDRAM Dimms.
-----
-
-!!3. What hardware should be used?
-
-!!3.1 Controller type
-
-
-
- Given all these options, if you're looking for a RAID solution,
-you need to think carefully about what you want. Depending on what
-you want to do, and which RAID level you wish to use, some cards may
-be better than others. SCSI-to-SCSI adapters may not be as good as
-host-based adapters, for example. Michael Neuffer (
-neuffer@kralle.zdv.uni-mainz.de), the author of the EATA-DMA
-driver, has a nice discussion about this on his
-Linux High Performance SCSI and RAID page.
-
-!!3.2 Enclosure type
-
-
-
- The enclosure type affects the hot swap-ability of the drive, the
-warning systems (i.e., whether there will be indication of failure,
-and whether you will know which drive has failed), and what kind of
-treatment your drive receives (for example, redundant cooling and
-power supplies). We used the DPT supplied enclosures which work
-extremely well, but they are expensive.
-----
-
-!!4. Installation
-
-!!4.1 Installing and configuring the hardware
-
-
-
- Refer to the instruction manual to install the card and the
-drives. For DPT, since a storage manager for Linux doesn't exist yet,
-you need to create a MS-DOS-formatted disk with the system on it
-(usually created using the command "format /s" at the MS-DOS
-prompt). You will also be using the DPT storage manager for MS-DOS,
-which you should probably make a copy of for safety.
-
-
- Once the hardware is in place, boot using the DOS system
-disk. Replace the DOS disk with the storage manager. And invoke the
-storage manager using the command:
-
-
-
-
-
-a:\ dptmgr
-
-
-
-
-Wait a minute or so, and you'll get a nice menu of options. Configure
-the set of disks as a hardware RAID (single logical array). Choose
-"other" as the operating system.
-
-
- The MS-DOS storage manager is a lot easier to use with a mouse,
-and so you might want to have a mouse driver on the initial system
-disk you create.
-
-
- Technically, it should be possible to run the SCO storage manager
-under Linux, but it may be more trouble than its worth. It's probably
-more easier to run the MS-DOS storage manager under Linux.
-
-!!4.2 Configuring the kernel
-
-
-
- You will need to configure the kernel with SCSI support and the
-appropriate low level driver. See the
-Kernel HOWTO for information on how to compile the kernel. Once you choose
-"yes" for SCSI support, in the low level drivers section, select the
-driver of your choice (EATA DMA or EATA ISA/EISA/PCI for most EATA DMA
-compliant (DPT) cards, EATA PIO for the very old PM2001 and PM2012A
-from DPT). Most drivers, including the EATA DMA and EATA ISA/EISA/PCI
-drivers, should be available in recent kernel versions.
-
-
- Once you have the kernel compiled, reboot, and if you've set up
-everything correctly, you should see the driver recognising the RAID
-as a single SCSI disk. If you use RAID-5, you will see the size of
-this disk to be 2/3 of the actual disk space available.
-
-!!4.3 Bootup messages
-
-
-
- The messages you see upon bootup if you're using the EATA DMA
-driver should look something like this:
-
-
-
-
-
-EATA (Extended Attachment) driver version: 2.59b
-developed in co-operation with DPT
-(c) 1993-96 Michael Neuffer, mike@i-Connect.Net
-Registered HBAs:
-HBA no. Boardtype Revis EATA Bus BaseIO IRQ DMA Ch ID Pr QS S/G IS
-scsi0 : PM2144UW v07L.Y 2.0c PCI 0xef90 11 BMST 1 7 N 64 252 Y
-scsi0 : EATA (Extended Attachment) HBA driver
-scsi : 1 host.
-Vendor: DPT Model: RAID-5 Rev: 07LY
-Type: Direct-Access ANSI SCSI revision: 02
-Detected scsi disk sda at scsi0, channel , id 8, lun
-scsi0: queue depth for target 8 on channel 0 set to 64
-scsi : detected 1 SCSI disk total.
-SCSI device sda: hdwr sector= 512 bytes. Sectors= 35591040
[[17378 MB
] [[17.4 GB]
-
-
-
-
-(The above display is for a setup with a single DPT SCSI controller,
-configured as RAID-5, with three disks of 9 GB each.)
-
-
- The messages you see upon bootup if you're using the EATA
-ISA/EISA/PCI driver should look something like this:
-
-
-
-
-
-aic7xxx: <Adaptec AHA-294X SCSI host adapter> at PCI 15
-aic7xxx: BIOS enabled, IO Port 0x7000, IO Mem 0x3100000, IRQ 15, Revision B
-aic7xxx: Single Channel, SCSI ID 7, 16/16 SCBs, QFull 16, QMask 0x1f
-EATA0: address 0x7010 in use, skipping probe.
-EATA0: 2.0C, PCI 0x7410, IRQ 11, BMST, SG 252, MB 64, tc:y, lc:y, mq:62.
-EATA0: wide SCSI support enabled, max_id 16, max_lun 8.
-EATA0: SCSI channel 0 enabled, host target ID 6.
-EATA/DMA 2.0x: Copyright (C) 1994-1997 Dario Ballabio.
-scsi0 : Adaptec AHA274x/284x/294x (EISA/VLB/PCI-Fast SCSI) 4.1.1/3.2.1
-scsi1 : EATA/DMA 2.0x rev. 3.11.00
-scsi : 2 hosts.
-scsi0: Scanning channel A for devices.
-Vendor: IBM OEM Model: DFHSS2F Rev: 1818
-Type: Direct-Access ANSI SCSI revision: 02
-Detected scsi disk sda at scsi0, channel , id , lun
-Vendor: SEAGATE Model: ST41650 TX Rev: DG01
-Type: Direct-Access ANSI SCSI revision: 02
-Detected scsi disk sdb at scsi1, channel , id , lun
-Vendor: TEAC Model: FC-1 GF 00 Rev: RV L
-Type: Direct-Access ANSI SCSI revision: 01 CCS
-Detected scsi removable disk sdc at scsi1, channel , id 3, lun
-Vendor: SONY Model: CD-ROM CDU-541 Rev: 2.6a
-Type: CD-ROM ANSI SCSI revision: 02
-Detected scsi CD-ROM sr0 at scsi1, channel , id 5, lun
-EATA0: scsi1, channel , id , lun , cmds/lun 21, sorted, tagged.
-EATA0: scsi1, channel , id 3, lun , cmds/lun 21, sorted.
-EATA0: scsi1, channel , id 5, lun , cmds/lun 21, sorted.
-scsi : detected 1 SCSI cdrom 3 SCSI disks total.
-SCSI device sda: hdwr sector= 512 bytes. Sectors= 4404489 [[2150 MB] [[2.2 GB]
-SCSI device sdb: hdwr sector= 512 bytes. Sectors= 2779518 [[1357 MB] [[1.4 GB]
-SCSI device sdc: hdwr sector= 256 bytes. Sectors= 4160 [[1 MB] [[.0 GB]
-
-
-
-
-(The above display is for a setup with two SCSI controllers, DPT
-PM3224W and and Adaptec AHA2940.)
-----
-
-!!5. Usage
-
-!!5.1 fdisk, mke2fs, mount, etc.
-
-
-
- You can now start treating the RAID as a regular disk. The first
-thing you'll need to do is partition the disk (using fdisk). You'll
-then need to set up an ext2 filesystem. This can be done
-by running the command:
-
-
-
-
-
-% mkfs -t ext2 /dev/sdxN
-
-
-
-
-where /dev/sdxN is the name of the SCSI partition. Once you do this,
-you'll be able to mount the partitions and use them as you would any
-other disk (including adding entries in /etc/fstab).
-
-!!5.2 Hot swapping
-
-
-
- We first tried to test hot swapping by removing a drive and putting
-it back in the DPT-supplied enclosure/tower (which you buy for an
-additional cost). Before we could carry this out to completion, one
-of the disks failed (as I write this, the beeping is driving me
-crazy). Even though one of the disks failed, all the data on the RAID
-drive was accessible.
-
-
- Instead of replacing the drive, we just went through the motions
-of hot swapping and put the same drive back in. The drive rebuilt
-itself and everything turned out okay. During the time the disk had
-filed, and during the rebuilding process, all the data was
-accessible. Though it should be noted that if another disk had failed,
-we'd have been in serious trouble.
-
-!!5.3 Performance
-
-
-
- Here's the output of the Bonnie program, on a 2144 UW with 9x3=17
-GB RAID 5 setup, using the EATA DMA driver. The RAID is on a dual
-processor Pentium Pro machine running Linux 2..33. For comparison,
-the Bonnie results for the IDE drive on that machine are also given.
-
-
-
-
-
--------Sequential Output-------- ---Sequential Input-- --Random--
--Per Char- --Block--- -Rewrite-- -Per Char- --Block--- --Seeks---
-MB K/sec %CPU K/sec %CPU K/sec %CPU K/sec %CPU K/sec %CPU /sec %CPU
-RAID 100 9210 96.8 1613 5.9 717 5.8 3797 36.1 90931 96.8 4648.2 159.2
-IDE 100 3277 32.0 6325 23.5 2627 18.3 4818 44.8 59697 88.0 575.9 16.3
-
-
-
-
- Some people have disputed the above timings (and rightly so---I've
-been unable to try it out on our machines since they're completely loaded)
-because the size of the file used may have led to it being cached
-(resulting in an unusually good performance report). Here are some
-timings with a 3344 UW controller:
-
-
-
-
-
--------Sequential Output-------- ---Sequential Input-- --Random--
--Per Char- --Block--- -Rewrite-- -Per Char- --Block--- --Seeks---
-MB K/sec %CPU K/sec %CPU K/sec %CPU K/sec %CPU K/sec %CPU /sec %CPU
-1000 1714 17.2 1689 6.0 1200 5.7 5263 40.2 7023 12.1 51.3 2.2
-
-
-
-
-And
here are some timings on a SCSI-to-SCSI RAID system:
-
-
-
-
-
--------Sequential Output-------- ---Sequential Input-- --Random--
--Per Char- --Block--- -Rewrite-- -Per Char- --Block--- --Seeks---
-MB K/sec %CPU K/sec %CPU K/sec %CPU K/sec %CPU K/sec %CPU /sec %CPU
-64 7465 100.0 70287 98.7 37012 97.7 8074 99.2 *****100.3 ***** 196.6
-128 7289 99.3 67595 98.5 35294 98.6 7792 97.6 *****100.3 ***** 195.8
-256 7222 98.8 44844 69.6 16096 51.8 5787 72.7 ***** 99.8 ***** 85.2
-512 7138 98.4 13871 23.2 7888 29.3 7183 89.3 16488 27.2 1585. 11.5
-1024 6908 95.8 12270 21.5 7161 25.4 7373 90.4 16527 28.2 123.8 1.8
-2047 6081 84.1 12664 22.6 7191 25.6 7289 89.5 16573 28.5 75.0 1.2
-***** results exceed column width (> 100 MB/sec, > 10000 seeks/sec)
-host: Dual PII 400 MHz, 2 x U2W, 512 MB RAM, no internal disks
-RAID: IFT 3102 UA 128 MB Cache, RAID-5, 6 x 9 GB
-OS: SuSE Linux 6.0 with Kernel 2.2.3
-
-
-----
-
-!!6. Features in the EATA DMA driver
-
-
- This section describes some of the commands available under Linux
-to check on the RAID configuration. Again, while references to the
-eata_dma driver is made, this can be used to check up on any
-driver.
-
-
- To see the configuration for your driver, type:
-
-
-
-
-
-% cat /proc/scsi/eata_dma/N
-
-
-
-
-where N is the host id for the controller. You should see something
-like this:
-
-
-
-
-
-EATA (Extended Attachment) driver version: 2.59b
-queued commands: 353969
-processed interrupts: 353969
-scsi0 : HBA PM2144UW
-Firmware revision: v07L.Y
-Hardware Configuration:
-IRQ: 11, level triggered
-DMA: BUSMASTER
-CPU: MC68020 20MHz
-Base IO : 0xef90
-Host Bus: PCI
-SCSI Bus: WIDE Speed: 10MB/sec.
-SCSI channel expansion Module: not present
-SmartRAID hardware: present.
-Type: integrated
-Max array groups: 7
-Max drives per RAID 0 array: 7
-Max drives per RAID 3/5 array: 7
-Cache Module: present.
-
-
-
-
-Type:
-Bank0: 16MB without ECC
-Bank1: 0MB without ECC
-Bank2: 0MB without ECC
-Bank3: 0MB without ECC
-Timer Mod.: present
-NVRAM : present
-SmartROM : enabled
-Alarm : on
-Host<->Disk command statistics:
-Reads: Writes:
-1k: 0
-2k: 0
-4k: 0
-8k: 0
-16k: 0
-32k: 0
-64k: 0
-128k: 0
-256k: 0
-512k: 0
-1024k: 0
->1024k: 0
-Sum : 0
-
-
-
-
- To get advanced command statistics, type:
-
-
-
-
-
-% echo "eata_dma latency" > /proc/scsi/eata_dma/N
-
-
-
-
- Then you can do a:
-
-
-
-
-
-% cat /proc/scsi/eata_dma/N
-
-
-
-
-to get more detailed statistics.
-
-
- To turn off advanced command statistics, type:
-
-
-
-
-
-% echo "eata_dma nolatency" > /proc/scsi/eata_dma/N
-
-
-----
-
-!!7. Troubleshooting
-
-!!7.1 Upon bootup, no SCSI hosts are detected
-
-
-
- This could be due to several reasons, but it's probably because
-the appropriate driver is not configured in the kernel. Check and make
-sure the appropriate driver (EATA-DMA or EATA ISA/EISA/PCI for most
-DPT cards) is configured.
-
-!!7.2 RAID configuration shows up as N different disks
-
-
-
- The RAID has not been configured properly. If you're using a DPT
-storage manager, you need to configure the RAID disks as a single
-logical array. Michael Neuffer (
-neuffer@kralle.zdv.uni-mainz.de) writes: "When you configure
-the controller with the SM start it with the parameter /FW0 and/or
-select Solaris as OS. This will cause the array setup to be managed
-internally by the controller."
-
-!!7.3 Machine/controller is shut down in the middle of a format
-
-
-
- As stated in the DPT manual, this is clearly a no-no and might
-require the disks to be returned to the manufacturer, since the DPT
-Storage Manager might not be able format it. However, you might be
-able to perform a low level format on it, using a program supplied by
-DPT, called clfmt in their utilities page. Read the
-instructions after unzipping the clfmt.zip file on how to use it (and
-use it wisely). Once you do the low level format, you might be able to
-treat the disks like new. Use this program carefully!
-
-!!7.4 SCSI_ABORT_BUSY errors produced during initial filesystem format
-
-
-
- When you do a mke2fs on the SCSI drive, you may see errors
-of the form:
-
-
-
-
-
-scsi: aborting command due to timeout : pid xxx, scsi0, channel , id
-2, lun
-write (10) xx xx xx xx xx xx xx xx xx
-eata_abort called pid xxx target: 2 lun: 0 reason: 3
-Returning: SCSI_ABORT_BUSY
-
-
-
-
-and this might end up causing the machine to freeze. I (and many
-others) have been able to fix this problem by simply reading one or
-two hundred MB from the RAID array with dd like this:
-
-
-
-
-
-% dd if=/dev/sdX of=/dev/null bs=1024k count=128
-
-
-
-
-
-
-
- During a format, a fast rush of requests for chunks of memory that
-is directly accessible is made, and sometimes the memory manager
-cannot deliver it on time anymore. The dd is a workaround
-that will simply create the requests sequentially instead of one huge
-heap at once like the format tends to create it.
-
-!!7.5 If all fails...
-
-
-
- Read the SCSI-HOWTO again. Check the cabling and the termination.
-Try a different machine if you have access to one. The most common
-cause of problems with SCSI devices and drivers is because of faulty
-or misconfigured hardware. Finally, you can post to the various
-newsgroups or e-mail me, and I'll do my best to get back to you.
-----
-
-!! 8. References
-
-
- The following documents may prove useful to you as you set up
-RAID:
-
-
-
-
-
-*
-DPT Technology Library
-*
-
-*
-EATA-DMA homepage
-*
-
-*
-Linux Disk HOWTO
-*
-
-*
-Linux Kernel HOWTO
-*
-
-*
-Linux SCSI HOWTO
-*
-
-*
-Multi Disk System Tuning HOWTO
-*
-
-*
-RAID Solutions for Linux
-*
-
-----
-
-!!9. Acknowledgements
-
-
- The following people have been helpful in getting this HOWTO
-done:
-
-
-
-
-
-* Andreas Koepf (
-A_Koepf@icp-vortex.com)
-*
-
-* Boris Fain (
-fain@zen.stanford.edu)
-*
-
-* Dario Ballabio (
-Dario_Ballabio@milano.europe.dg.com)
-*
-
-* Heiko Rommel (
-Heiko.Rommel@Uni-Bielefeld.DE)
-*
-
-* Jos Vos (
-jos@xos.nl)
-*
-
-* Michael Neuffer (
-neuffer@kralle.zdv.uni-mainz.de)
-*
-
-* Ralph Wallace (
-rwallace@rwallace.interaccess.com)
-*
-
-* Russell Brown (
-russell@lutton.lls.com)
-*
-
-* Syunsuke Ogata (
-Syunsuke_Ogata@appear.ne.jp)
-*
-
-* Tom Brown (
-tbrown@baremetal
.com)
-*
-
-----
+Describe
[HowToDPTHardwareRAID
] here.
